INDUSTRIAL LUBRICANTS


Stationary Gas Engine Oils

Find the right stationary gas engine oil

What ash level is required?

Do you operate with non-traditional gas sources (i.e. bio, sewage, landfill, etc.)?

Do you operate with Non-traditional gas sources (i.e. bio, sewage, landfill, etc.)?

Do you need cold start-up capability and pumpability performance or have the need for ash pounding protection?

Do you pre-treat gas (<200 ppm H2S, No halogens & siloxanes)?

Are you running your engines at low loads (<60% MCR)?

Are you interested in higher performance engine cleanliness and extended drain intervals beyond the conventional?

Do you have stoichiometric engines in high nitrating conditions?

Do you want to extend drains beyond SENTRON LD 5000?

Add to calendar

Result

Bestmatch

SENTRON™ ASHLESS 40 (0.05% WT ASH)

SENTRON™ ASHLESS 40 is recommended primarily for 2-stroke cycle gas engines but may be used in certain 4-stroke cycle gas engines.

SENTRON™ ASHLESS 40 minimizes combustion chamber and spark plug deposits.

Minimizes port plugging.

Bestmatch

SENTRON™ CG 40 PLUS (0.52% WT ASH)

SENTRON™ CG 40 PLUS is uniquely formulated for 4-stroke cycle engines in severe service landfill and other similar contaminated gas operations.

Controls acids by effective neutralization TBN.

It does this without contributing to additional harmful ash deposits that can damage an engine.

Can withstand the pressures that come from running contaminated gas applications and problems caused by high halogen gas levels, especially where higher BMEP engines are used.

Suitable for use in engines with catalytic converters.

Verified/Approved for use in Caterpillar, INNIO Jenbacher, MAN and MWM.

Bestmatches

  • SENTRON™ LD 5000 (0.57% WT ASH)

    SENTRON™ LD 5000 provides excellent performance for up to 200% longer drain intervals and exceptional overall engine protection for maximum reliability and savings.*

    Advanced piston cleanliness.

    Petro-Canada Lubricants recommends for use in Caterpillar, INNIO Waukesha, INNIO Jenbacher, MWM, MAN, MTU, Bergen, Wartsila and other turbocharged or naturally aspirated, stoichiometric or lean burn engines that require low ash gas engine oil.

    Suitable for use in engines with catalytic converters.

  • SENTRON™ LD 8000 (0.52% WT ASH)

    SENTRON™ LD 8000 provides the same engine durability and cleanliness offered with SENTRON™ LD 5000.

    SENTRON™ LD 8000 provides significantly extended drain intervals over Leading Global Conventional Competitor.

    Excellent engine cleanliness.

    Outstanding acid neutralization capability without contributing to excess ash in the combustion zone of the engine.

    Ideal for use in 4-stroke engines, in natural pipeline gas, pre-treated sewage/bio-gas and selective pre-treated process gas fuel sources.

    Suitable for high nitrating and low nitrating environments.

    Verified/Approved for use in Caterpillar, INNIO Jenbacher, INNIO Waukesha, MWM, MAN, MTU, Siemens and other turbocharged or naturally aspirated, stoichiometric or lean burn engines.

*Performance results may vary due to factors such as, but not limited to, engine optimization, load, fuel gas quality, proper maintenance, type of engine and application.

Bestmatch

SENTRON™ LD 8000 (0.52% WT ASH)

SENTRON™ LD 8000 provides the same engine durability and cleanliness offered with SENTRON™ LD 5000.

SENTRON™ LD 8000 provides significantly extended drain intervals over Leading Global Conventional Competitor.

Excellent engine cleanliness.

Outstanding acid neutralization capability without contributing to excess ash in the combustion zone of the engine.

Ideal for use in 4-stroke engines, in natural pipeline gas, pre-treated sewage/bio-gas and selective pre-treated process gas fuel sources.

Suitable for high nitrating and low nitrating environments.

Verified/Approved for use in Caterpillar, INNIO Jenbacher, INNIO Waukesha, MWM, MAN, MTU, Siemens and other turbocharged or naturally aspirated, stoichiometric or lean burn engines.

Bestmatch

SENTRON™ LD 8000 (0.52% WT ASH)

SENTRON™ LD 8000 provides the same engine durability and cleanliness offered with SENTRON™ LD 5000.

SENTRON™ LD 8000 provides significantly extended drain intervals over Leading Global Conventional Competitor.

Excellent engine cleanliness.

Outstanding acid neutralization capability without contributing to excess ash in the combustion zone of the engine.

Ideal for use in 4-stroke engines, in natural pipeline gas, pre-treated sewage/bio-gas and selective pre-treated process gas fuel sources.

Suitable for high nitrating and low nitrating environments.

Verified/Approved for use in Caterpillar, INNIO Jenbacher, INNIO Waukesha, MWM, MAN, MTU, Siemens and other turbocharged or naturally aspirated, stoichiometric or lean burn engines.

Bestmatch

SENTRON™ LD 5000 (0.57% WT ASH)

SENTRON™ LD 5000 provides excellent performance for up to 200% longer drain intervals and exceptional overall engine protection for maximum reliability and savings.*

Advanced piston cleanliness.

Petro-Canada Lubricants recommends for use in Caterpillar, INNIO Waukesha, INNIO Jenbacher, MWM, MAN, MTU, Bergen, Wartsila and other turbocharged or naturally aspirated, stoichiometric or lean burn engines that require low ash gas engine oil.

Suitable for use in engines with catalytic converters.

*Performance results may vary due to factors such as, but not limited to, engine optimization, load, fuel gas quality, proper maintenance, type of engine and application.

Bestmatch

SENTRON™ LD 3000 (0.47% WT ASH)

SENTRON™ LD 3000 provides extended oil life and excellent control of engine deposits, even when there is a need for added high temperature deposit control.

Excellent high temperature control of varnish deposits to minimize valve sticking issues.

Recommended for use in 4-stroke and some 2-stroke engines.

Approvals/Verifications:

  • Caterpillar G3300-G3600.
  • INNIO Waukesha Co-generation listing (TA 12-1880AS).
  • MWM.

Bestmatch

SENTRON™ VLA 40 (0.30% WT ASH)

SENTRON™ VLA 40 is a “very” low-ash stationary gas engine oil, specifically designed for engines running at low loads (<60% MCR).

SENTRON™ VLA 40 is formulated with a very low ash content to address issues observed with low loaded engines such as increased oil consumption and therefore excessive ash deposit build up which leads to spark plug fouling, valve issues and piston/liner.

Bestmatch

SENTRON™ LD SYNTHETIC BLEND (0.53% WT ASH)

Pour Point: -42˚C/-44˚F

SENTRON™ LD SYNTHETIC BLEND is a multi-grade synthetic blend formulation offering advanced piston cleanliness and cold pumpability performance down to -20˚C/-4˚F.

Advanced piston cleanliness.

Petro-Canada Lubricants recommends for use in Caterpillar, INNIO Waukesha, and other turbocharged or naturally aspirated, stoichiometric or lean burn engines that require a low ash gas engine oil.

Suitable for use in engines with catalytic converters.

INNIO Waukesha Co-generation listing (TA 12-1880AS).

Bestmatch

SENTRON™ CG 40 (0.93% WT ASH)

SENTRON™ CG 40 is designed for 4-stroke cycle gas engines running in severe service such as co-generation, sewage or sour gas or low halogen landfill gas operations.

Verify suitability for engines equipped with catalytic convertors sensitive to elevated levels of Zn and P.

*Note: Not all designs run optimally with mid ash oils (see low ash stream for alternatives).

Verified/Approved for use in Caterpillar, INNIO Waukesha, INNIO Jenbacher, MAN, MWM, MTU, Siemens and others.

Bestmatch

SENTRON™ SP 40 (0.75% WT ASH)

SENTRON™ SP 40 is specially formulated for high Brake Mean Effective Pressure (BMEP) stationary gas engines operating with steel pistons. It is suitable for use in 4-stroke engines requiring medium ash content.

SENTRON™ SP 40 is formulated with advanced additive techNology to prevent harmful deposit formation in the top ring grooves of steel piston engines operating with high piston temperatures.

It also provides outstanding oxidation / nitration resistance and acid neutralization capability.

Approved for use in INNIO Jenbacher and Bergen engines.

Bestmatches

  • SENTRON™ VTP 0W-30

    • 0.58% wt ash.

    • All the features of SENTRON™ VTP 0W-30 formulated for use in cold climates.
    • Ideal for extreme cold starts/cold flow pumpability (<-35˚C/<-31˚F).
    • Not recommended for certain engines fitted with catalytic converters; especially if catalyst is sensitive to elevated Zinc and Phosphorous versus conventional SGEO Zn and P levels.
  • SENTRON™ VTP 10W-40

    • 0.59% wt ash.

    • Recommended for use in gas fueled engines in oil and gas extraction and agricultural irrigation that require high zinc for improved valve train wear protection.
    • Excellent anti-wear properties for engines with sliding cam followers.
    • Minimizes combustion chamber and spark plug deposits.
    • Not recommended for certain engines fitted with catalytic converters; especially if catalyst is sensitive to elevated Zinc and Phosphorous versus conventional SGEO Zn and P levels.
  • SENTRON™ VTP 10W-40 PLUS

    • 0.68% wt ash.

    • Designed for stationary gas applications that need additional anti-wear characteristics (ie. gasoline converted engines to natural gas) due to the valve train and/or for engines where extreme improved low temperature performance benefits are desired due to cyclic engine on-off cycles.
    • Applications include smaller remote gas well head engines and gas line booster engines that are low emission.
    • Not suitable for some engines with catalytic converters due to higher Zn and P levels.
    • Extended drains and excellent durability.
  • SENTRON™ Stationary Gas Engine Oils are premium performance, long-life engine oils for stationary gas engines and compressors in a wide variety of applications.

  • SENTRON™ LD 8000’s extended drain intervals can result in lower maintenance costs, less used oil to dispose of and a more efficient and profitable operation.

  • Outstanding wear protection prevents scoring of cylinder liners and piston ring wear, while reducing carbon build-up.