GREASES


VULTREX™ OGL

The VULTREX™ OGL family of grease-based gear lubricants are sophisticated, next-generation lubricants designed for use on large, heavy-duty, open gear drives as well as bearings and exposed sliding surfaces. This machinery is most commonly found in open-pit mining operations using large mining shovels, drills, excavators, and draglines. VULTREX™ OGL line of greases is designed with a darkening agent that allows mining operators to more easily identify gears that have adequate grease applied.

VULTREX™ OGL SYNTHETIC 2200 is a high viscosity aluminum complex-based, solvent-free open gear lubricant specifically designed to provide “ONE LUBRICANT” for mining shovels, draglines, excavators, drills and haul trucks. It is intended for summer use or for year-round use in warmer climates, with a lower temperature limit of -15°C/5°F. It meets the P&H 464 Open Gear Lubricant specification. It also meets the Caterpillar Global Mining (formerly Bucyrus International) SD 4713 specification. VULTREX™ OGL SYNTHETIC 2200 is also approved by Komatsu for lubrication of slew ring gear on Komatsu hydraulic shovels.

Refer to the product properties here.

VULTREX™ OGL SYNTHETIC ALL SEASON 680 is an aluminum complex based, solvent-free open gear lubricant. Its wide operating temperature range allows it to be used from fall through spring seasons at most mines. VULTREX™ OGL Synthetic All Season 680 resists water wash-off from the shovel stick or rack and pinion systems under all weather conditions, and has a low temperature limit of -40°C/-40°F. It meets the P&H 464 Open Gear Lubricant specification and the Caterpillar Global Mining (formerly Bucyrus International) SD 4713 specification. VULTREX™ OGL SYNTHETIC ALL SEASON 680 is approved by Komatsu for lubrication of slew ring gear on Komatsu hydraulic shovels.

Refer to the product properties here.

VULTREX™ OGL HEAVY 6200 is an aluminum complex based, solvent-free open gear lubricant with higher viscosity and thicker consistency than the other VULTREX™ OGL lubricants. It is intended for the most demanding open gear lubrication requirements, including heavily loaded hoist gears and high temperature applications. It meets the P&H 464 Open Gear Lubricant specification and the Caterpillar Global Mining (formerly Bucyrus International) SD 4713 specification, including the special requirements for electric mining shovel hoist gear lubrication.

Refer to the product properties here.

Typical characteristics are shown below:

VULTREX™

 

OGL Synthetic 2200

OGL Synthetic All Season 680

OGL Heavy 6200

Soap Type

Aluminum Complex

Aluminum Complex

Aluminum Complex

Color

Black

Black

Black

Worked Penetration @ 25°C

390

374

361

Dropping Point °C/°F

214/417

208/406

248/478

Weld Point, kg

800

800***

800

Operating Range, °C

-15 to 40

-40 to 25

-5 to 60

Operating Range °F

5 to 104

-40 to 77

23 to 140

Minimum Dispensing,** Centralized System °C/°F

-15/5

-40/-40

-5/23

* Plastic cone used

** Based on pumpability test, but is dependent on the design and type of the dispensing systems, length and diameter of the lines, the mode of application and rate of pressurization.

*** Measured before the addition of diluent, as per the Caterpillar Global Mining (formerly Bucyrus International) SD 4713 specification.

Symbols

  1. Agriculture
  2. Consumer Automobile
  3. Construction
  4. Food & Beverage
  5. Forestry
  6. Heavy-Duty Transportation
  7. General Manufacturing
  8. Medium-Duty Transportation
  9. Mining
  10. Corrugated Packaging
  11. Gas Plants, Pipelines & Power Generation
  12. Rail
  13. Transit
  14. Waste Operations